Find Products for Your Vehicle
HEAVY DUTY AXLES-VOODOO TECHNOLOGY
MSRP: $495.95
- If you’re ATV or UTV has a lift kit or extended A-arms, and requires long travel suspension, you need Moose Heavy Duty Axles-With Voodoo Axle Technology. Our revolutionary design provides ultra-high strength, and the ability to operate at angles other can't.
- Increased Range of Motion To accommodate suspension travel the axles utilize a slip spline that allows the axle to compress and extend 2". This helps to prevent disengagement of the inner CV joint from the transaxle when the suspension is at full droop. Telescoping axle bars are carried on linear motion ball bearings for smooth action that won't bind under load.
- Increased Operating Angle Typical axles use inboard CV joints that must both operate at an angle, and allow suspension travel. This dual purpose design limits articulation angle to about 25°, while travel is limited to 1.25" - 1.5", which is inadequate for ATV's and UTV's with lift kits, or long travel suspension. These axles utilize fixed Rzeppa inner CV joints that allow 45° of articulation, while a slip spline in the axle shaft provides 2" of travel.
COMPLETE CLUTCH KITS
MSRP: $19.95 - $203.95
- Designed to outperform OEM aftermarket clutches
- A one sotp shop for all your clutch components
- Includes friction plates, steel plates, clutch springs and a clutch cover gasket
- Replacement clutch cover gaskets available
COMPLETE FRONT AND REAR AXLE ASSEMBLIES
MSRP: $231.95 - $394.95
- Fully assembled outboard CV joint
- Heavy-duty puncture-resistant boot and axle bar
- All are front except as noted
- Some models come with a universal joint and yoke assembly or a fully assembled inboard CV joint
COUNTERSHAFT SEAL KITS
MSRP: $14.95 - $16.95
- Kit includes hardened steel bushing, an upgraded seal, an O-ring (where applicable) and a snap ring or lock washer (where applicable)
- Made in the U.S.A.
CV BOOT GUARDS
MSRP: $64.95
- Provide protection for most 4WD UTVs
- Tough, lightweight aluminum diamond-plate construction
- An inexpensive investment that can pay off in a hurry - saves costly repairs to CV joints by protecting boots and CVs themselves
- Protected and undamaged boots keep lubrication in, water and dirt out
CV BOOT KITS
MSRP: $13.95 - $29.95
- Replace those dangerously worn, inexpensive CV boots before dirt, dust and grime destroy expensive CV joints
- Tougher than stock and come with everything you need to complete the job
- Heavy-duty puncture-resistant boot
- Comes with grease and clamps
DIFFERENTIAL BEARINGS
MSRP: $9.95 - $133.95
- Kits include high-speed EMQ quality bearings with type TC rubber seals
- Garter-spring inner lips and optimal sealing from rubber-covered outside diameter seals
- Kit includes everything needed to completely service differential conveniently - saves time and money
FAST BOOT II
MSRP: $2.95 - $17.95
- ATV CV boot that fits virtually all ATVs
- Additional rib to allow boot to expand for larger joints
- Improved clamp retaining ridges
- Squared off inside edge to keep clamp retaining ridge upright
FRONT AND REAR CV HALFSHAFTS
MSRP: $177.95 - $218.95
- Heavy-duty fully assembled outboard joint and boot assembly
- Axle bar, inboard puncture-resistant boot, clamps and grease
- Polaris halfshafts include axle bar
- Front and rear halfshafts charted separately
FRONT AND REAR CV JOINT KITS
MSRP: $99.95 - $134.95
- Heavy-duty fully assembled inboard and outboard joint assembly
- Heavy-duty puncture-resistant boot, clamps and grease
- Sold each
FRONT AND REAR CV REBUILD KITS
MSRP: $69.95 - $115.95
- Improve OEM quality - heavy-duty puncture-resistant boot, cage, race and balls, clamps and grease
- Step-by-step instruction sheet included
- Made in the U.S.A.
LIFT KITS
MSRP: $32.95 - $274.95
- Increase performance in deep ruts, mud and snow
- Better ground clearance over stumps and rocks
- Simple bolt-on operation with clear instructions
- Increased ground clearance for less tire/fender rub
MASTER CYLINDER REBUILD KITS
MSRP: $15.95 - $40.95
- Complete kits to rebuild the master cylinder
- Each kit contains all necessary components
MUD-PROOF SOLID REAR DISC ROTORS
MSRP: $119.95
- Used by professional off-road racing teams around the world
- Made from high-carbon-content stainless steel, which offers greater friction than standard discs
- No-holes design greatly prolongs brake pad life in muddy conditions
- Cut with a CAD/CAM laser machine, not stamped like stockers
MXR BLADE REAR ROTORS
MSRP: $109.95
- Made with high-carbon 410 stainless steel
- 100% laser-cut design
- Lighter weight blade design for improved feel and stopping power plus more efficient cooling
- High quality Blanchard grinding providing precise flatness and attractive finish
QUALIFIER BRAKE PADS
MSRP: $19.95
- Latest generation of Kevlar®-based organic material
- Progressive feel and rider feedback
- No rotor wear and quiet
REAR WHEEL BEARING UPGRADE KITS
MSRP: $51.95 - $65.95
- Replaces two side-by-side bearings with one double-row bearing
- 30% increase in load-carrying capacity and bearing life
- Kits include bearings and seals
REPLACEMENT ROTORS
MSRP: $59.95 - $99.95
- Manufactured from 420 high-carbon stainless steel
- Engineered to offer greater strength and durability than OEM
- Offers greater friction and longer life than OEM at an affordable price
- CAD/CAM laser-cut and finish-ground for a distortion-free flat profile
SHOCK SPRING WEDGES
MSRP: $39.95
- Flexible spring spacers install in minutes and offer additional front or rear suspension stiffness while using snow plows, sprayers and spreaders
- Fit most utility ATV stock shocks with spring diameter up to 3"
- Sold in pairs
CLUTCH FRICTION PLATES
MSRP: $54.95 - $144.95
- Features an exclusive high heat-resistance friction material for fade-free performance
- Ready to install, no need to soak in oil
- Designed to ensure ultra-smooth power delivery
CLUTCH STEEL DRIVE PLATES
MSRP: $32.95 - $69.95
- Made of steel, not aluminum
- Won't expand and fade like stock OEM plates
- 300% longer life than stock
- Sold in sets of 6 or 7
CLUTCH SPRINGS
MSRP: $9.95 - $11.95
- Precision wound using the finest chrome silicone wire
- Heat treated and shot peened for maximum life
- Offers stronger performance than OEM springs
STAINLESS STEEL BRAIDED BRAKE LINES
MSRP: $28.95 - $116.95
- Swivel union ends for easy kink- and stress-free installation
- Made in the U.K. by Venhill Engineering to Moose Racing's highest specifications; feature top-quality DuPont Teflon®-coated hose, wrapped with British-made stainless steel and PVC-coated for protection and great looks; designed to withstand a minimum of 1
- Rubber protection boots and extra-rigid tubing protect vulnerable areas from heat and impact and prevent hose flex under compression
- Give a large performance increase by reducing expansion under pressure, and absorption of water when compared to stock rubber hoses
STEERING STEM BEARING KITS
MSRP: $33.95 - $40.95
- Designed as a drop-in replacement to upgrade OEM ball-type bearings to taper bearings, or a high-quality replacement if your bike comes with taper bearings stock
- Tapered roller bearings provide decreased maintenance along with less wear, smoother operation and longer life
- Kits come complete with both upper and lower taper bearing cups, cones, and most include top and bottom seals
- Made in the U.S.A.
SWINGARM BEARING KITS
MSRP: $29.95 - $83.95
- Repair kits include all the bearings, seals, shafts and spacers required for a complete rebuild
- Constructed from OEM-quality components at a fraction of the cost
TIE-ROD ASSEMBLY UPGRADE KITS
MSRP: $102.95
- Upgrade from 10mm tie-rod ends that are prone to failure to Moose's heavy-duty 12mm style tie-rod assemblies
- Each kit contains two tie-rods, four tie-rod ends along with cotter pins and jam nuts
TIE-ROD END KITS
MSRP: $14.95 - $88.95
- Each kit contains two quality tie-rod ends - one left-hand thread and one right-hand thread - along with the cotter pins and jam nuts
- Rod ends are heavy-duty direct replacements at a fraction of OEM cost
- Sold in kits for one tie-rod; two kits required per vehicle
UPPER AND LOWER A-ARM UPGRADE KIT
MSRP: $126.95
- OEM design incorporates small spherical bearings that carry the load of the entire front end
- Over time, spherical bearings become loose and external seals break due to excess play and that allows contamination to pass into the assembly
- Upgrade kit contains acetal thermoplastic bushings and hardened ground pins for the entire front end of the machine
UPPER AND LOWER SHOCK BEARING KITS
MSRP: $13.95 - $37.95
- Each kit contains the bearing and all of the seals, spacers and pins to rebuild the shock bearings to factory specifications
- Constructed from OEM quality components at a fraction of the cost
WHEEL BEARINGS
MSRP: $7.95 - $72.95
- Kits include all required bearings and seals
- Front kits are per wheel; rear kits are per axle unless noted
- High-speed, low-drag bearings are EMQ quality
- Bearing seals are double-lipped rubber that provides superior exclusion of water, dirt and sand with improved grease retention
WHEEL CYLINDER REPAIR KITS
MSRP: $27.95 - $43.95
- For wheel cylinders of front hydraulic drum brakes
- Include all necessary parts to repair one side brake of system at a fraction of the OEM cost
3-WHEEL STEERING STEM/4-WHEEL LOWER STEERING STEM BEARING KITS
MSRP: $6.95 - $37.95
- Designed as a drop-in replacement to upgrade OEM ball-type bearing sets to taper bearings, or a high-quality replacement for bikes that come with stock taper bearings
- Tapered roller bearings provide decreased maintenance along with less wear, smoother operation and longer life
- Kits come complete with both upper and lower taper bearing cups and cones and seals
A-ARM BEARING AND SEAL KITS
MSRP: $6.95 - $78.95
- Direct OEM replacement parts designed to rebuild the A-arm to factory specification
- Precision-ground A-arm shaft manufactured from 52100 heat-treated bearing steel for improved performance and extended life
- Kit contains bearings, pins, spacers and seals to rebuild one A-arm
ATV REAR INDEPENDENT SUSPENSION KITS
MSRP: $23.95 - $112.95
- Cost-effective kit containing all bearings, bushings, seals, shafts and miscellaneous components to repair the rear upper and lower A-arms and knuckle
- Two kits required per vehicle
ATV/UTV HIGH PERFORMANCE DRIVE BELTS
MSRP: $69.95
- Designed to dominate any type of terrain
- Made with extra-strong p-aramid cord reinforcement and engineered fiber-loaded neoprene compounding
- Delivers the "muscle" and durability demanded by today's high-performance engines
- Tested under severe field conditions
ATV/UTV HIGH-PERFORMANCE PLUS DRIVE BELTS
MSRP: $99.95
- Engineered for 800cc and larger engines
- Specially-formulated high-temperature Neoprene® with the highest level of aramid fiber loading available, delivers trail-blazing performance for the most aggressive riders
- An innovative break-though design features deeper cogs on top and rounded cogs on the bottom for the ultimate in flexibility and longer belt life
- Gives extreme riders the best out-of-the-hole acceleration, throttle response and durability
BALL JOINT AND KING PIN KITS
MSRP: $19.95 - $52.95
- Ball joint kit is sold per A-arm and comes with snap ring and cotter pin
- King pin kits (used in applications where a king pin was used rather than a ball joint) includes all bushings, pins and seals needed for repair
- Ball joints feature heavy-duty steel cases with POM-M90 bearing material for long life
- Put an end to premature Honda ball joint failure by upgrading from the OEM aluminum joint to our heavy-duty steel joint
BILLET CLUTCH BASKETS
MSRP: $203.95 - $237.95
- New design improves clutch performance and heat dissipation
- Precision machined from billet T-6 aircraft quality aluminum
- Hard anodized for longer wear resistance than OEM design
- Superior tensile strength and hardness
BOOT CLAMPS
MSRP: $1.95 - $32.95
- Set your own desired amount of torque
- Boot kits offer the free-end style clamp
BRAKE BLEEDER CAPS
MSRP: $5.95
- Replace missing or cracked bleeder caps
- Keep mud and dust out of your brake lines
- High-temp-resistant materials and universal fitment make these caps a convenient replacement
- Sold in a 2-pack
BRAKE CALIPER PINS
MSRP: $6.95 - $19.95
- Each kit includes required quantities of brake pad hanger pins
- Made by Nissin, the OE manufacturer in Japan
BRAKE CALIPER REBUILD KITS
MSRP: $13.95 - $37.95
- Each kit includes all necessary rubber components and pad hanger pins if its applicable
- Made by Nissin, an OE manufacturer in Japan
BRAKE LINE CLAMPS
MSRP: $32.95
- Billet aluminum clamps provide a clean way to attach brake lines to ATV A-arms
- Two-piece design with Allen bolt closure fits any 1" o.d. A-arms; works with most aftermarket brake lines
- Sold in pairs
BRAKE PADS AND SHOES BY DP BRAKES
MSRP: $16.95 - $46.95
- Pads are constructed of durable sintered metal, which stands up to the toughest conditions and provides equal braking power wet or dry
- Brake shoes are asbestos-free and offer good durability and performance